時間：2011-08-11 18:26來源：藍天飛行翻譯 作者：航空 點擊：次
|
滑油管路 oil line 滑油壓力表 oil pressure indicator 滑油溫度表 oil temperature indicator 滑油散熱器 oil cooler 滑油量傳感器 oil quantity transmitter 滑油壓力傳感器 oil pressure sensor 滑油溫度傳感器 oil temperature sensor 滑油濾旁通警告電門 oil filter bypass warning switch 潤滑 lubrication/lubricate 潤滑劑 lubricant 潤滑組件 lubrication unit 探測器 detector 回油 scavenge 回油過濾 scavenge filter 主滑油/燃油熱交換器 main oil/fuel heat exchanger 發動機滑油消耗高（滑油量快速減少）high engine oil consumption (oil quantity decreased at a quick rate) 發動機滑油壓力/油量指示 Engine oil pressure/quantity indication 1) 高 High 2) 斷續或空白 Intermittent or blank 3) 低（琥珀色） Low (amber) 4) 低或零（紅色） Low or zero (red) 5) 不精確，斷續，保持恒定或空白 Inaccurate, intermittent, remain constant, or blank. 6) AF 檢查發現左發滑油箱口蓋金屬鏈丟失 Do AF check and find the metal chain of cap to oil tank at L/H is lost. 7) 航后檢查發現后貨艙滑油儲備盒缺少2罐滑油。Two bottles of oil in the oil store box has been found lack during AF check. 8) 關車時左發滑油壓力警告系統瞬時閃亮（紅色）The oil pressure warning system of the L/H engine flashed(red light) when shutting down the engines. 9) 航后檢查發現EEC自檢有79-31342滑油壓力DISAGREE信息。The information DISAGREE of the oil pressure appeared when doing the BITE of EEC AF check. 10) 重力添加發動機滑油 Add the engine oil by gravity filling procedure 11) 往啟動機加滑油 Fill the starter with oil 12) Fill the CSD with oil 給CSD加滑油 13) Serve CSD spline with oil 用滑油勤務CSD花鍵軸 14) Replace oil supply filter element更換滑油供油濾濾芯 15) Replace scavenge oil filter element更換回油濾濾芯 16) Replace scavenge oil filter element更換滑油搜油油濾 17) Serve the engine oil by gravity fill procedure重力加油步驟勤務發動機滑油 ATA80 起動 起動 start 發動機振動指數高/空白/波動/為零。High/Blank/Fluctuating/Zero Engine vibration(VIB) 主發起動時，APU 排氣出現刺耳噪音。APU exhaust made sharp noise when main engine started 發動機起動 engine start 1) 機組反映左發地面起動后起動電門無法自動返回off位 . The crew reported that the engine starting switch could not return to off position automatically. 2) 機組口頭反映左發啟動手柄至CUT OFF位時左發關車慢.The crew reported orally that the time of the L/H engine shut down slowly when putting the start lever to the CUT OFF position. 3) Replace L/H engine starter 更換左發啟動機 4) Inspect magnetic chip detectors檢查磁堵 發動機起動活門 engine start valve 1) EGT上升但點火不正常（即將發生熱起動），燃油流量及管道壓力正常，發動機已起動。EGT increased but ignition was abnormal (impending hot start), fuel flow and duct pressure indication was normal. |
